What is the default Harley security code?

VIDEO-If your Harley Davidson is equipped with a factory installed alarm then you really need to immediately change your security PIN code. Harley puts a standard factory preset PIN code and it is usually 31313.

How do you reset the security PIN on a Harley Davidson?

Press right turn signal switch 1 time and release. The new digit (a) will replace the current in odometer window. Enter second digit (b) of new PIN by pressing left turn signal switch b times. Press right turn signal switch 1 time and release.

How do I reset my Harley after tipping?

To reset the system, upright the bike, set the “kill” button in the “run” position and cycle the ignition off, on then off. It’s also in the manual.

What is the red key light on a Harley-Davidson for?

Registered. If the security light (the key) stays on solid (not flashing) and the bike starts and runs, it means the bike has thrown a DTC. (diagnostic trouble code) It is essentially the equivalent of the “check engine” light on a car. The procedure for checking the code is posted in the electrical section.

THIS IS INTERESTING:  Which market deal with long term securities which have a maturity period of over 1 year?

How much does it cost to replace a Harley-Davidson key fob?

Lost Harley Key Replacement

Compare to other motorcycle and car key, Harley Davidson key is one of the best keys to lose. The average cost for a replacement key made by vin is $50 and can be done by most if not all local authorized Harley Dealer.

Where is the ignition key on a Harley-Davidson?

The ignition switch is on the left side of the vehicle between the engine cylinders. Unlock: Insert key and turn clockwise to unlock the thumb lever. Remove the key from ignition switch before operating motorcycle.

How do you unlock a 2016 Harley-Davidson?

2016 Harley-Davidson Street Glide Special — Owner’s Manual – Page #25

  1. Turn fork to full left position.
  2. See Fork Lock: FLHR, FLHRC.
  3. To unlock fork, insert key and turn clockwise to UNLOCK position.
  4. Turn fork to full left position.
  5. See Ignition Switch.
  6. Insert key and turn key to LOCK position.

How do I disable the anti-theft?

Steps to Disable Car Anti-Theft System

  1. Use Key Fob. The most obvious way to get around the anti-theft system is to use the key fob.
  2. Try Key in Door. As the key fob starts to die, it might no longer disable the alarm.
  3. Examine Key/Cylinder.
  4. Turn on Ignition.
  5. Remove Alarm Fuse.
  6. Disconnect Battery.

How do I bypass immobilizer?

You can bypass the immobilizer by placing the key in keyhole hence deactivating the car’s immobilizer to remote start. The added security with Mobokey allows the security to be activated as soon as the phone moves away from the car, so you don’t have to worry about car security.

THIS IS INTERESTING:  Should I uninstall McAfee from my laptop?

What does the red light on my motorcycle mean?

Green/Blue: A system is active and working as it should. Amber: There’s a fault somewhere – take extra care and have a look as soon as possible. Red: There’s a serious fault on your motorbike – stop driving as soon as it is safe to do so.

Why is my Harley not recognize key fob?

If your fob doesn’t work, make sure the battery is good and inserted correctly. If dead, you should be able to get a replacement from a dealer. If you don’t know your PIN, you should. A dealer can reset it for you, but I’m sure they are pretty proud of that service.

How long do Harley key fob batteries last?

HD recommend that you replace the battery in your Harley-Davidson key FOB every 12 months. Use and dime or five cent coin to open the key FOB body. Step 1: Insert a five cent piece or similar blade into the thumbnail slot on the side of the FOB to separate the two halves.

How do I activate my Harley Davidson alarm?


  1. turn key to ignition.
  2. within 2 seconds of turning the switch to ignition, press and hold both turn signals until confirmation (key icon flashes quickly)
  3. enter code (you enter with the left turn signal, and confirm with the right.
  4. after you confirm the 5th digit, it is disarmed (key icon stops blinking)

What does the Harley key fob button do?

The key fob remotely locks and unlocks the fork lock switch, saddlebags and Tour-Pak. The key fob can actuate the locks while the motorcycle is on or off.

THIS IS INTERESTING:  How do I update Dell Data Protection Encryption?

What is angle of bank in aircraft?

the angle between the lateral axis of an aircraft in flight and the horizontal.

Where is the bike key number?

Using your motorcycle’s key code

The code is either printed on the key itself or on the metal tab which is attached to the original key. In either case, you can check the code and share with this code number with the dealer to get the key replaced. This will not require taking the motorcycle or changing the lock.

How do you start a Harley without fob or PIN?


Immediately hold both turn signal indicators until FIVE dashes appear in the odometer gauge. Select the first digit of your PIN (a) by pressing the left turn signal button (a) times. Press the right turn signal switch one time to move to the next digit.

Does anti-theft light drain battery?

The anti-theft light won’t drain your battery.

But, if you leave the car alarm to go off for long, it can drain the battery.

How do you disconnect a factory alarm system?

A large number of factory alarms turn off once you put the key in the lock of driver’s or even passenger doors. You can also try a similar method – pressing the lock or unlock button on the remote fob. Unlocking the doors with the right remote fob will shut down most fabric alarms.